GearUP AVP-63 Automatic Voltage Protector-220V

Key FunctionsProtection Features  Over-voltage Protection: Cuts off power if voltage exceeds the set threshold (P-3).  Under-voltage Protection: Disconnects load if voltage drops below the set limit (P-5).  Over-current Protection: Trips when current surpasses the configured max (P-9) after a delay (P-10).  Automatic Recovery: Restores power after fault conditions (adjustable via P-15).  Fast Power-Down: Emergency cutoff (enabled via P-14).Monitoring & Display  Real-time voltage display (AC/DC).  Real-time current display (AC only; DC mode shows voltage only).  Indicators for faults (>V, A) and normal operation (POWER).Programmable Settings  Adjustable thresholds for voltage/current, recovery times, and calibration (P-1 to P-17).  Password protection (P-17) to prevent unauthorized changes.2. Technical Specifications3. Setup & Operation GuideA. Initial ConfigurationPower Connection:  Wire terminals (N-L) to AC/DC source within rated limits.Menu Navigation:  Use front-panel buttons to adjust parameters (P-1 to P-17).B. Critical SettingsC. CalibrationVoltage: Adjust via P-8 (±10%).Current: Calibrate with P-12 (±10%).Frequency (AC only): Fine-tune with P-13 (±2.5%).D. Safety & RecoveryManual Reset: Required if auto-recovery (P-15) is disabled.Event Logging: Overcurrent counts (P-11) track fault history.4. Usage NotesDC Mode: Current display disabled; only voltage monitored.Energy Saving: Enable P-16 to reduce idle power consumption.Altitude Warning: Performance may degrade above 2000m.Note: Refer to the device’s manual for detailed wiring diagrams and safety compliance.

categories

Category List

All products

• 
• 
• 

Details:

• Warranty
  year (Burn and physical damage not applicable)

Key Functions

1. 
   Protection Features

  Over-voltage Protection: Cuts off power if voltage exceeds the set threshold (P-3).  Under-voltage Protection: Disconnects load if voltage drops below the set limit (P-5).  Over-current Protection: Trips when current surpasses the configured max (P-9) after a delay (P-10).  Automatic Recovery: Restores power after fault conditions (adjustable via P-15).  Fast Power-Down: Emergency cutoff (enabled via P-14).

1. Monitoring & Display

  Real-time voltage display (AC/DC).  Real-time current display (AC only; DC mode shows voltage only).  Indicators for faults (>V, A) and normal operation (POWER).

1. Programmable Settings

  Adjustable thresholds for voltage/current, recovery times, and calibration (P-1 to P-17).  Password protection (P-17) to prevent unauthorized changes.

2. Technical Specifications

3. Setup & Operation Guide

A. Initial Configuration

1. 
   Power Connection:

  Wire terminals (N-L) to AC/DC source within rated limits.

1. Menu Navigation:

  Use front-panel buttons to adjust parameters (P-1 to P-17).

B. Critical Settings

C. Calibration

• 
  Voltage: Adjust via P-8 (±10%).

• Current: Calibrate with P-12 (±10%).

• Frequency (AC only): Fine-tune with P-13 (±2.5%).

D. Safety & Recovery

• 
  Manual Reset: Required if auto-recovery (P-15) is disabled.

• Event Logging: Overcurrent counts (P-11) track fault history.

4. Usage Notes

• 
  DC Mode: Current display disabled; only voltage monitored.

• Energy Saving: Enable P-16 to reduce idle power consumption.

• Altitude Warning: Performance may degrade above 2000m.

Note: Refer to the device’s manual for detailed wiring diagrams and safety compliance.

GearUP AVP-63 Automatic Voltage Protector-220V

950 BDT1,050 BDTSave 100 BDT

1

add_to_cartbuy_now

Details:

• Warranty
  year (Burn and physical damage not applicable)

Key Functions

1. 
   Protection Features

  Over-voltage Protection: Cuts off power if voltage exceeds the set threshold (P-3).  Under-voltage Protection: Disconnects load if voltage drops below the set limit (P-5).  Over-current Protection: Trips when current surpasses the configured max (P-9) after a delay (P-10).  Automatic Recovery: Restores power after fault conditions (adjustable via P-15).  Fast Power-Down: Emergency cutoff (enabled via P-14).

1. Monitoring & Display

  Real-time voltage display (AC/DC).  Real-time current display (AC only; DC mode shows voltage only).  Indicators for faults (>V, A) and normal operation (POWER).

1. Programmable Settings

  Adjustable thresholds for voltage/current, recovery times, and calibration (P-1 to P-17).  Password protection (P-17) to prevent unauthorized changes.

2. Technical Specifications

3. Setup & Operation Guide

A. Initial Configuration

1. 
   Power Connection:

  Wire terminals (N-L) to AC/DC source within rated limits.

1. Menu Navigation:

  Use front-panel buttons to adjust parameters (P-1 to P-17).

B. Critical Settings

C. Calibration

• 
  Voltage: Adjust via P-8 (±10%).

• Current: Calibrate with P-12 (±10%).

• Frequency (AC only): Fine-tune with P-13 (±2.5%).

D. Safety & Recovery

• 
  Manual Reset: Required if auto-recovery (P-15) is disabled.

• Event Logging: Overcurrent counts (P-11) track fault history.

4. Usage Notes

• 
  DC Mode: Current display disabled; only voltage monitored.

• Energy Saving: Enable P-16 to reduce idle power consumption.

• Altitude Warning: Performance may degrade above 2000m.

Note: Refer to the device’s manual for detailed wiring diagrams and safety compliance.